AROYA Solus Products
Trolmaster TrolMaster Hydro X MBS-S8 CO2 Sensor measures CO2 in grow rooms. $ 179.00 $ 222.00
Description The optional CO2 Sensor (MBS-S8) measures the CO2 PPM within the growing area. Using the MBS-S8 allows the users to connect and control their supplemental CO2 system using the Hydro-X. *Used in combination with one or more DSC-1 CO2 device modules.
Trolmaster TrolMaster Hydro X MBS-TH Hydro-X Replacement 3 in 1 sensor $ 68.25 $ 79.00
3-in-1 Temp/Humid/Light sensor for the Hydro-X system. Note: This is a replacement or spare part. The main controller comes with a sensor already. Note: This is a replacement or spare part. The main controller comes with a sensor already. "Sensors should remain dry and clean to prevent premature failure. Do not spray foreign substances or allow water / condensate on the sensors"
Trolmaster TrolMaster Hydro X MBS-SD Hydro-X Smoke Detecor $ 55.10 $ 58.00
The optional Smoke Detector (MBS-SD) can alert the user to smoke within their growing area at ALL TIMES. Up to 5 smoke detectors can be connected to a single Hydro-x controller. If ANY of the smoke detectors determine there is smoke in the area, the user will receive a user-alert on their phone to alert them to the potential problem BEFORE the problem gets out of hand. "Sensors should remain dry and clean to prevent premature failure. Do not spray foreign substances or allow water / condensate on the sensors"
Trolmaster TrolMaster Hydro X MBS-PAR Hydro-X Full Spectrum Quantum Sensor $ 437.00 $ 442.00
The Full Spectrum Quantum Sensor (MBS-PAR) provides accurate and cost-effective measurement of photosynthetically active radiation (PAR) from all light sources used to grow plants. The full-spectrum quantum sensor has a spectral range of 389 to 692 nm ± 5 nm. The improved spectral response increases the accuracy of LED measurements.
Trolmaster TrolMaster Hydro X WD-2 Water Detector $ 69.83 $ 73.50
The optional Water Detector WD-2 allows the user to detect water leaks or water on the floor of the facility. Simply place the water sensor at floor level (or wherever you want to watch out for water leaks). Up to 5 Water detectors can be connected to a single Hydro-x controller. If ANY of the sensor detects a water leak, the unit will send a user-alert to notify user of a water leak.
Trolmaster TrolMaster Hydro X MBS-PRO Hydro-X Temp/Humid/CO2/Light 4-in-1 Sensor $ 377.95 $ 399.00
The MBS-PRO 4-in-1 sensor combines a precision air temperature, humidity, CO2 (PPM) sensor and photocell to create the perfect all-in-one environmental sensor. It is designed for Hydro-X Pro system only. Assembled using a new water-resistant plastic injected enclosure, the MBS-PRO can be placed in multiple locations throughout the growing area to provide spot measurements from multiple sensors (Up to 50 sensors can be connected to the Hydro-X Pro) The sensors can then be used together (averaged) or separately in order to control a specific section of the grow area by assigning a sensor to a specific control device. The MBS-PRO features a built-in LCD display to show the current conditions of that sensor which provide the ease of onsite monitoring. It also features a new “push-lock” connection to make installation easy.Please Note: The MBS-Pro requires the SPH-1 for supplemental power. "Sensors should remain dry and clean to prevent premature failure. Do not spray foreign substances or allow water / condensate on the sensors"
Popular in the store
Other customers also love these best selling products
AROYA Aroya Solus EC Meter. Soil Moisture EC and Temp Sensor For Grow Medium $ 524.00 $ 535.00
We ship direct from our warehouse. Free expedited ground shipping to the lower 48 states. Volume pricing available. Contact us on Chat. Overstock Promo Code $25 Off! Use "SaveOnSolus" at the checkout payment window. Dial in plant nutrition and watering schedules with SOLUS. No subscription fees or App cost. Free to use after purchase. If you're looking for a high-precision EC spot measurement tool to help you maximize your yield and quality, look no further than the SOLUS. This innovative tool pairs a pinpoint soil sensor with a seamless app to give you all the data and insights you need to take your cultivation to the next level. With the SOLUS, you can easily and quickly take spot measurements of your substrate, without any datalogging required. So why wait? Get the SOLUS and start growing better today! DESCRIPTION Yield. Quality. You always want more. If you’re a serious grower — even at home – you’re never not ready for big data and analytics. To grow better, you must first know better, and there’s no tool like SOLUS to mine your substrate for insights and help your harvest flourish. Use the SOLUS for easy and quick spot measurements of your substrate, no datalogging required and no information is retained. Water. Temp. EC. All impact the quality and yield of your crop. To level up your home growing requires precision at every stage, across every variable. With SOLUS, you’re in control of it all. Reap a harvest full of insights right on your phone. Simple to download, and even simpler to detect your sensor. Learn About EC Mine the insights buried in your substrate The SOLUS Sensor Kit combines the industry’s top soil sensor with a wireless analysis powerhouse. Together with the free SOLUS by AROYA app, they enable high-precision water content, temperature and electrical conductivity spot checks. The information SOLUS gathers helps growers maximize their substrate and unlock maximum yield potential. Learn more about the Solus on our YouTube Channel here: Quality Legendary sensor technology The product of more than 20 years of soil moisture research and technological refinement, the TEROS 12 sensor is trusted by scientists, farmers and growers alike. The TEROS 12’s ruggedized body lasts ten years or more. Its stainless-steel sensor needles slide easily into any substrate. It even ships with a free reusable sensor installation tool to help growers align the sensor perfectly for consistent, accurate measurements. INCLUDES One TEROS 12 Sensor One ZSC Handheld Bluetooth Module For App Connectivity APP Download - search AROYA SOLUS on the Apple or Android App stores FEATURES Quick and easy WC, EC and temp spot-checks Secure – won’t store data or monitor measurements over time Wirelessly pairs with any iOS or Android mobile device using Bluetooth Easy installation with installation tool Steel needles cut through the soil for better soil-sensor contact Robust, epoxy body for tough field conditions Dependable, long-life sensor Large volume of influence Ferrite core eliminates cable noise Device Operating System Compatibility and System Requirements The mobile device must be capable of using Bluetooth® Low Energy (BLE). The mobile device operating system compatibility is Apple iOS 10 or greater and Android OS 4.3 or greater. NOTE: Location services must be enabled to use the Bluetooth capabilities of the ZSC. This is a requirement set by the Android operating system (OS). TEROS 12 Operation Manual Download Link
FGI FGI Far Red LED Grow Light. 700-760nm Spectrum Enhancer. $ 99.25 $ 149.00
Overview Rugged, waterproof, glass lens, 100-277 VAC. This unit is built to last. Our far red lightbar is the most popular 4' long 730nm grow light on the market today. Industrial grade construction. All aluminium housing. Internal LED driver. About Growing with Far Red Energy Far-red light is good for plant growth. It can increase photosynthesis, enhance growth, and increase plant size. Far-red light is significant to plants because it increases the ability of plants to capture light. Plants use light not only as a source of energy, but also for information about the surrounding environment. Far-red light is typically not absorbed much by plant leaves, and it doesn't drive any photosynthesis because it is mostly reflected off leaves. However, if a plant "senses" a greater ratio of far-red to normal light then it "knows" that obstructions or other plants are close to it. Far-red light can also regulate leaf angle and increase plant height and leaf area, via expression of associated genes, to capture more light energy. The lightbar features a crystal lens that covers the diodes, making it waterproof and resistant to overspray. Additionally, the lightbar is designed to be easily moved and bumped around, making it one of the most versatile and user-friendly grow lights on the market. However, what sets this light apart from others is its ability to stimulate plant morphology. By emitting a high intensity of far red light, the FGI Far Red Lightbar encourages plant growth and development, making it the perfect choice for any serious gardener or farmer. Use far red energy in veg to keep plants compact and strong. Recent studies at Utah State University by Dr Bruce Bugbee, have proven that additional energy, even in the red spectrum, keeps plants more compact. The science of using far red light on plants Recent studies at the University of Texas El Paso / University of Texas Arlington, concluded that plants exposed to full spectrum plus dosing with far red spectrum, increased overall plant mass/yield and also improved terpene profiles. Read the study here. The light coverage of this product is unmatched. It will fully cover a 4' wide grow tray in bloom and generally covers a 2' wide swath. We recommend a pair for each 4x4 grow space and this unit comes with hardware which allows you to position it inside the frame of most 5 and 8 bar full spectrum LEDs. This light system is one of the best on the market and will give your plants the light they need to thrive. Order now and be sure to get your grow space set up correctly so you can achieve maximum light coverage. Targeting the Emerson Effect. The Emerson Effect is the name given to the increase in the rate of photosynthesis that occurs when chloroplasts are exposed to far red energy just before the nighttime lights off cycle. This effect was first discovered by scientist Alexander Emerson in 1883, and it has since been extensively studied by plant biologists. While the Emerson Effect is typically associated with increases in photosynthesis, it can also lead to other changes in plant physiology, such as increased cell division and growth. One way to take advantage of the Emerson Effect is to use our supplimental far red LED grow light for 10-15 minutes after full spectrum lights are turned off. If you are looking to create the ideal environment for your plants, an LED grow light can help you to achieve the Emerson Effect. Far Red Spectrum Use We recommend 2 units per 4x4 grow space for daytime enhanced PPFD delivery. Height over canopy should be the same as your full spectrum LED but it will not hurt the plants to hang beneath a 4x4 LED. Time General use: Studies indicate that dosing with far red light is most effective with 4 hours on, 4 off, and 4 on. We recommend a digital wall timer, or if using TrolMaster the DSP-1 (for 110V connections) or a DSP-2 (for 240V). Emerson Effect: 10-15 minutes after full spectrum lights are turned off. Plant Morphology Theory Plants use phytochrome to detect and respond to red and far-red wavelengths. Phytochromes are signaling proteins that promote photomorphogenesis in response to red light and far-red light. Phytochrome is the only known photoreceptor that absorbs light in the red/far red spectrum of light (600-750 nm). (source: Wikipedia) Far Red light is believed to create a competitive response in plants, pushing desirable terpene production and assisting in the formation of trichomes. Read more about Far Red and extended spectrum in this recent release from Design Lights Consortium: Read It Here ~Technical Specs~ Product 30W（±5%） PPF 72.1 umols/s 100-277VAC,50/60 Hz 102.3BTU IP65 44.88”x 2.24”x 1.53” 4.4 lbs Photometric Test Report Download Product Warranty (see our warranty here) 3 year warranty
Trolmaster TrolMaster Hydro X HCS-1 Hydro X Grow Room Controller $ 312.50 $ 329.00
Our Story: Forever Green is one of the largest US distributors of TrolMaster products. We ship direct from our warehouse (no drop shipping). 60 day returns with free expedited ground shipping to the lower 48 states. And low cost expedited shipment worldwide. This modular system is easy to install and expand, and can be fully customized to your needs. With the free TrolMaster App, you can access all system settings and alerts from anywhere, anytime. The Hydro-X system is compatible with most grow lights brands, HVAC systems, mini-split air conditioners, commercial dehumidifiers and humidifiers, as well as CO2 generators or regulators. So whether you're looking to maintain optimal growing conditions in your indoor garden the Hydro-X system has you covered. Includes the TrolMaster 3 in 1 sensor bundle and RJ16 cables. A turn-key environmental sensor system to tune up your gardens success. Looking for a trusted high volume TrolMaster Official Distributor in North America? Look no further than Forever Green Indoors! We're the leading provider of quality TrolMaster products and accessories, and we're here to help you keep your indoor spaces looking their best. This controller is as user friendly as it gets, and installing and setting it up is simple. It's compatible with just about every major grow light, HVAC system, dehumidifier/humidifier, and even CO2 system. You can use the free TrolMaster app, and achieve complete control of your grow room remotely, freeing you from the grow room and getting you back to doing the things you enjoy. Whats Included With The Hydro-X System: Hydro-X Environment Controller (x1) 3-in-1 Sensor for Temperature, Light, and Humidity (x1) RJ12 Cable Set (x1) Male-to-Male 16ft RJ12 Cable (x1) Male-to-Male 4ft RJ12 Cable (x1) RJ12 T-Splitter (x1) Achieve Complete Grow Room Control With The Hydro-X With one piece of equipment, you can essentially control anything you need in your grow room. There are more than 17 separate types of control modules, granting you the ability to connect the Hydro-X to A/C's and HVAC To put it simply, the TrolMaster Hydro-X Environment Controller With 3-in-1 Sensor is the most intelligent and versatile system on the market. The Hydro-X System Features A Modular Design Another great feature of the Hydro-X Environment Control System is that you can control and customize every last detail of the controller. The modular design means you can configure the separate components in unique ways to create the best environment for your plants because every grow is different. You can control up to 512 different grow lights on two separate channels, and operate different systems simultaneously. Just about every lighting brand and product on the market is compatible with the Hydro-X with different adapters. NOTE: 2 knob fixtures allowing individual control of 2 different bulbs can NOT be controlled by the Hydro X Currently we have: LMA-11 for Phantom - Lighting Adapter P LMA-12 for Dimlux - Lighting Adapter D LMA-13 for Sun System - Lighting Adapter S LMA-14 Lighting Adapter F for FGI brand LEDs LMA-14 for HIDs like Growers Choice/Illuminar/PL LMA-14 for LEDs like Fluence/Next light/Spectrum King LMA-15 for DLI - Lighting Adapter DLI LMA-T for ThinkGrow - Lantern Schedule Adapter F Using the LMA-14 Adapter (Adapter F) for multiple lights The LMA-14 Adapter can be used for 24 Drivers (LEDs) or 40 Ballasts with either the HCS-1 or HCS-2 Hydro-X controllers. Both the Hydro-X Controllers have 2 line lights giving the ability to control double the amount of each type of light (48 LEDs and 80 Ballasts). All the other controlled modules are connected to the device channel. For temperature control we have: TS-1/TS-2 for HVAC Systems The TS-1 (4 Wire) & TS-2 (6 Wire) thermostat stations are designed to replace a thermostat connected to a conventional cool only HVAC unit. ARS-1 for Mini Split System The ARS-1 mini-split air conditioner controller is a universal controller that works with most mini-split air conditioners (and some window-type AC units too), as long as the unit came with an IR / infrared remote controller. DST-1 for Temperature-Controlled Outlets (120 Volt) The TrolMaster DST-1 Temperature control modules allow the user to easily connect and control standard heating or cooling devices to the Hydro-x. Any heating or cooling device that is 10-amps at 120 volts or less can be controlled by the DST-1. DST-2 for Temperature-Controlled Outlets (240 Volt) The TrolMaster DST-2 Temperature control modules allow the user to easily connect and control standard heating or cooling devices to the Hydro-x. Any heating or cooling device that is 10-amps at 240 volts or less can be controlled by the DST-2. For humidity control we have: HS-1 for Commercial Dehumidifiers The HS-1 is the best way to control your dehumidifiers by eliminating the need to control the high-amperage / inrush current associated with dehumidifiers. DSH-1/DSH-2 for Humidity-Controlled Outlets The TrolMaster DSH-1 (120 Volt) & DSH-2 (240 Volt) Humidity control / device modules allow the user to easily connect and control standard humidifying or dehumidifying devices to the Hydro-x. DSC-1 for CO2-Controlled Outlets The TrolMaster DSC-1 CO2 control / device module allows user the to easily connect and control standard supplemental CO2 devices or CO2 exhaust controls to the Hydro-x. Any CO2 device that is 10-amps @ 120 volts or less can be controlled by the DSC-1. DSP-1/DSD-1 The TrolMaster DSP-1 (120 Volt) program device module (timer module) works like a multi-function timer. The DSP-1 allows the user to easily connect any device that needs to be controlled by TIME to the Hydro-x. The Trolmaster DSD-1 Dry-contact module provides a simple and flexible solution to who want to connect & control devices to the Hydro-X using a dry-contact or relay to activate the device. All of these items are listed at the top under the custom options tabs or if you would like to view them individually they are all listed on our TrolMaster brand page here. https://forevergreenindoors.com/collections/trolmaster
Trolmaster TrolMaster Hydro X LMA-14 Lighting Adapter F for 0-10V control of grow lights. $ 55.00 $ 58.00
The LMA-14 lighting adapter is specially designed to control a wide variety of lighting systems including FGI brand LEDs and HIDs. TrolMaster’s Hydro-X system can control most of the horticultural lighting fixtures sold on the market today. Most light manufacturers provide the ability to control their lighting systems using what known as a low-volt control. That low-volt control can take many forms and communication protocols. TrolMaster makes several types of lighting adapters (LMA units) that allow the Hydro-x to control lights using their low-volt control option.